Pin 1 starts at the HF-Input. All Positions do count, also the ones which only shows a hole in the housing!

TYP ...-148C (u.a.??)

  1   LNC/LNB 14/18 Volt in
  2
  3
  4   AFC out
  5   S-Meter
  6   +5 Volt
  7   Basisband-Out
  8   Ref. for AFT/AFC
  9
10  Tuning voltage out  (siehe Anmerkung zur Abb. 2)
11  +28 Volt (for PLL-)
12  Port 3 (Output  I²C)
13  Port 6 (Output  I²C)
14  SDA (I²C-BUS)
15  SCL (I²C-BUS)

TYP ...-432A (a.o.??)

  1
  2   LNC/LNB 14/18 Volt in
  3
  4
  5   AFC out
  6   +5 Volt
  7   Basisband-Out
  8   Ref. for AFT/AFC
  9
10
11   +28 Volt (for PLL-Abst.)
12   Port 4 (Output  I²C)
13   Port 5 (Output I²C)
14   SDA (I²C-BUS)
15   SCL (I²C-BUS) 

 

If you will not control the tuner by I2C you can feed pin 10 with the tuning voltage

.Pin 11 is not connected. IT is advised to cut the track as shown at the picture above. 
The PLL is very stabil!

1   (bn) +LNC
2   (ge) AGC out
3   (rt) +12 Volt
4   (or) +5 Volt (for prescaler?)
5   (gn) BaseBand out
6   AFC out
7   (ws) Tuning voltage input
8   (Cinch) Osc. prescaler out

Sharp-Tuner BSFA 75G06 Same, without Pin 8

1   +LNB
2   +5 Volt (for prescaler)
3   Prescaler output
4   +12 Volt
5   Tuning voltage
6   AGC or AFC ???
7   BaseBand out
8   AFC or AGC ???

Pin 1 at F-Connector

1    +5 Volt for prescaler
2    Tuning voltage input
3    IF Bandwidth (0 Volt = 27 MHz, 12 Volt = 16 MHz)
4    S-Meter
5    +12 Volt
6    AFT/AFC on/off (on = 12V)
7    BaseBand out
8
9
10  Prescaler out 

Pin 1 at F-Connector 

1    12/18 Volt for LNC (lower connector)
2    12/18 Volt for LNC (upper connector)
3    Ground
4    +5 Volt (Prescaler and PLL)
5    (PLL) ?
6    Tuning voltage input
7    ?
8    (PLL) ?
9    (PLL) ?
10  ?
11  +12 Volt
12  BaseBand out deemph.
13  Ground
14  BaseBand out
15  AGC out (ca.0-5 V)

The IF-Filter consists of 3 stages and is a little bit tunable.

1   12/18Volt for LNC/LNB
2   BaseBand out
3   Tuning Error Voltage
4   +12 Volt
5   AGC

6   Tuning Voltage
7   +5 Volt Prescaler

8   Prescaler output (VCO/256)

This Tuner has a 70 MHz IF-Output. It has no Demodulator.
IF-Amplifier and Demodulator are inside the ODE 514 together with the Tuner at one PCB and can be used for homebuild ATV-Rx

1    +12/18 Volt for LNC/LNB
2    +12 Volt
3    Tuning voltage
4    AGC in (or Fixed 1.5 Volt)

1    HF Input (950-1750 MHz)
2    Ground
3    +12 Volt  (max 15 V.)
4    Tuning Voltage (max 30V)
5    Ground
6    BaseBand Out
7    +12 Volt  (max 15 V.)
8    Tuning Voltage
9    Prescaler Output (f osc / 2)
10  +5 Volt (for prescaler and IF)

This tuner is not very good for weak signals. There is no PLL-, but an Quadratur-Demodulator, which has a better Signal-Noise figure. There is no OFW-Filter in the IF, but an easy 3-stages LC-Filter with open air coils. It gives a home brew amateur a lot of options!