MAV-11SM
Frequency
MHz		 GAIN, dB Maximum Power, dBm Dynamic Range VSWR Absolute
Maximum
Rating		 DC Power Thermal
resistance
Øjc
°C/W
fL - fU Min. Output
(1 dB
Comp.)		 Input
(no
damage)		 NF
dB
Typ.		 IP3
dBm
Typ.		 In
Typ.		 Out
Typ.		 I
(mA)		 P
(mW)		 Cur-
rent
(mA)		 Volt(V.)
50-1000 9.00 +17.50 +13.00 3.60 30.00 1.50 1.70 80.00 550.00 60.00 5.50 125.00
Lw=low range(fL to fU/2)  U=upper range(fU/2 to fU)

Pin Connections
Port RF in RF Out DC Case GND Not Used
cb 1 3 3 2,4 -



Case Style - RRR137 (inch,mm )   weight: 0.015 grams.
A B C D E F G H J
.28
7.112		 .14
3.556		 .030
0.762		 .020
0.508		 .145
3.683		 .110
2.794		 .006
0.152		 .010
0.254		 .030
0.762
K L M N P Q R S T
                 
Tolerance: .x ± .1  .xx ± .03  .xxx ± .015 inch.
Material and Finish:
    Case material: plastic. Lead Finish: tin-lead plate.
Marking:
    RF output is identified by index mark, model dash number by alphanumeric code.
Special Tolerances:
    Lead width ±.010; lead thickness ±.005 inch.
Packaging:

Packaging information:
Tape Width(mm): 12
Reel Size(inches): 7
Device Cavity Pitch(mm): 8
Devices Per Reel: 500

 Notes:
• Minimum gain at highest frequency. Full temperature range, except room temperature for Dash-4 models.
• Thermal resistance Øjc is from hottest junction in the device to the mounting surface of the leads.
• Model number designated by alphanumeric code marking.
• Permanent damage may occur if any of these limits are exceeded. These ratings are not intended for continuous normal operation.
• For Amplifier Selection Guide, please click here.
For Amplifier Environmental Specifications, please click here.
• For Surface Mount Environmental Specifications, please click here.
Re-flow soldering information is available in "Surface Mount" article.
• Low frequency cutoff determined by external coupling capacitors.
• Frequency at which output power, NF and IP3 are specified: 500 MHz.
• Non-hermetic
• Typical Biasing Configuration ERA/MAR/MAV/RAM/VAM
• Prefix letter (optional) designates assembly location.
• Reliability predictions and normal operation conditions are applicable at current specified.
• General Quality Control Procedures and Environmental Specifications are given in Mini-Circuits Guarantees Quality.
Hi-Rel, MIL description are given in Hi-Rel and MIL
• Prices and Specifications subjects to change without notice.

FREQ
(MHz)		 S11 (Input Return Loss) S21 (Power Gain) S12 (Isolation Out-in) S22 (Output Return Loss)
dB Mag Ang dB Ang dB Mag Ang dB Mag Ang
0.50 -26.85 0.76 -22.00 19.30 167.00 -24.40 0.06 54.00 -26.85 0.77 -22.00
5.00 -37.95 0.20 -79.00 13.70 164.00 -16.50 0.15 12.00 -38.38 0.21 -83.00
50.00 -37.50 0.04 -75.00 12.70 174.00 -16.40 0.15 2.00 -42.67 0.05 -136.00
100.00 -38.17 0.04 -81.00 12.60 171.00 -16.40 0.15 2.00 -42.73 0.05 -137.00
500.00 -41.87 0.09 -124.00 12.10 141.00 -15.80 0.16 6.00 -43.17 0.15 -144.00
1000.00 -44.14 0.18 -161.00 10.70 106.00 -14.70 0.18 6.00 -44.76 0.26 -173.00
1500.00 -44.66 0.28 171.00 9.10 77.00 -13.50 0.21 2.00 -44.24 0.35 163.00
2000.00 -43.46 0.37 149.00 7.60 52.00 -13.00 0.22 -5.00 -42.92 0.43 140.00
2500.00 -42.48 0.45 133.00 6.10 33.00 -12.70 0.23 -10.00 -41.94 0.47 125.00
3000.00 -41.44 0.52 118.00 4.60 14.00 -12.60 0.23 -16.00 -40.98 0.50 112.00